top of page

Level 4 vs Level 5 Drywall Finish: What the Spec Means and What It Costs

Writer: St. Louis Drywall Pros
St. Louis Drywall Pros
Oct 26
3 min read

Updated: 1 day ago

Level 4 is the standard commercial finish. Level 5 adds a full skim coat and is worth specifying wherever light rakes across a wall.

The Gypsum Association's GA-214 defines six finish levels, 0 through 5. On most St. Louis tenant improvements and new construction, the spec calls for Level 4, with Level 5 in lobbies, corridors with wall-wash lighting, and anywhere gloss or dark paint is going on.

Level 4

  • All joints and interior angles get tape embedded in compound plus two separate coats over flat joints and one over interior angles

  • Fasteners and accessories get three coats of compound

  • Surface is smooth and free of tool marks and ridges

  • Right for flat or eggshell paint, textured finishes and most wallcovering with a primer

Level 5

  • Everything in Level 4, plus a thin skim coat of joint compound or a spray-applied skim over the entire surface

  • Eliminates the difference in texture and porosity between paper face and compound, so paint sheen is uniform

  • Required for gloss, semi-gloss and enamel paints, and where severe lighting (windows, downlights, wall grazers) will show joints

  • Adds a full pass of labor and material, typically a measurable premium per square foot over Level 4

What drives the cost difference

Level 5 is a labor item. The skim coat is one more full-surface application, a sand, and a primer check. On a 20,000 sq ft TI with 9,000 sq ft of Level 5 walls, expect the Level 5 area to carry roughly a quarter to a third more finishing labor than the Level 4 area. The material cost is small; the time is not.

How to spec it so bids compare

  1. Call out the finish level by room or wall type on the finish schedule, not just in the spec section

  2. Note the paint sheen and any wall-wash or grazing lights, since that is what justifies Level 5

  3. Ask subs to price Level 5 as a separate line so alternates are clean

  4. Confirm who primes: a Level 5 skim should be primed before paint, and the paint sub and drywall sub both need to know whose scope that is

Where finish levels matter most

Residential remodels often need a closer look because old framing, patched areas, and mixed surfaces can make a wall harder to finish cleanly. A basement project, for example, may include new drywall next to existing ceilings, boxed beams, utility chases, and patched corners. In that kind of space, the finish level and the texture strategy should be planned together.

Commercial work has its own pressure points. Offices, restaurants, schools, senior living spaces, and tenant improvements often have long corridors, bright lighting, and strict turnover schedules. If the finish level is not clearly defined in the scope, the risk of rework goes up. That can affect paint schedules, inspections, and final punch lists.

In both settings, ceilings deserve special attention. Ceiling surfaces usually show flaws faster than walls because light hits them differently and viewers see them from multiple angles. A ceiling that looks acceptable at first glance can still show joints once primer and paint are applied.

Common mistakes when finish levels are not specified

The most common mistake is assuming all drywall finishing means the same thing. It does not. One person may expect a paint-ready smooth wall while another is pricing a basic taped finish intended for texture.

Another problem is changing the finish after the work is underway. If a project starts with a texture plan and later switches to smooth painted walls, the original finish level may not support that change. That means extra coats, more sanding, and additional cost.

Lighting is another issue people underestimate. Walls that look fine under work lights can show defects once natural light or permanent fixtures are in place. That is why experienced finishers ask about windows, fixture layout, and final paint choices before calling a wall ready.

Then there is the repair factor. Patches, water damage areas, and additions rarely blend well without proper finishing. Matching an existing wall is not just about putting mud on the seam. It takes judgment, especially when tying new drywall into old surfaces with existing texture or years of paint buildup.

Send plans for a bid

St. Louis Drywall Pros bids commercial drywall, metal stud framing and acoustical ceilings across Greater St. Louis, with line-item pricing back within 48 hours. Send plans here or call 314-691-2444.


Related guides and services

This post is part of our commercial drywall resources for GCs, builders and owners in Greater St. Louis. Send plans for a bid or call 314-691-2444.

Recent Posts

See All

Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
  • Facebook
  • Twitter
  • LinkedIn

At St. Louis Drywall Pros, we believe in building more than just structures; we’re committed to building trust. Our team delivers quality and reliability in every project, ensuring your vision comes to life seamlessly. With us, you can expect professionalism and dedication to excellence. Let us help you create spaces that stand the test of time.

bottom of page